[Code of Federal Regulations] [Title 49, Volume 5, Parts 400 to 999] [Revised as of October 1, 1996] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR581] [Page 770-773] TITLE 49--TRANSPORTATION CHAPTER V--NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 581--BUMPER STANDARD Sec. 581.1 Scope. 581.2 Purpose. 581.3 Application. 581.4 Definitions. 581.5 Requirements. 581.6 Conditions. 581.7 Test procedures. Authority: Secs. 103, 119, Pub. L. 89-563, 80 Stat. 718 (15 U.S.C. 1392, 1407); sec. 102, Pub. L. 92-513, 86 Stat. 947 (15 U.S.C. 1912); delegation of authority at 49 CFR 1.50. [[Page 771]] Source: 42 FR 24059, May 12, 1977, unless otherwise noted. Sec. 581.1 Scope. This standard establishes requirements for the impact resistance of vehicles in low speed front and rear collisions. Sec. 581.2 Purpose. The purpose of this standard is to reduce physical damage to the front and rear ends of a passenger motor vehicle from low speed collisions. Sec. 581.3 Application. This standard applies to passenger motor vehicles other than multipurpose passenger vehicles. Sec. 581.4 Definitions. All terms defined in the Motor Vehicle Information and Cost Savings Act, Pub. L. 92-513, 15 U.S.C. 1901-1991, are used as defined therein. Bumper face bar means any component of the bumper system that contacts the impact ridge of the pendulum test device. Sec. 581.5 Requirements. (a) Each vehicle shall meet the damage criteria of Secs. 581.5(c)(1) through 581.5(c)(9) when impacted by a pendulum-type test device in accordance with the procedures of Sec. 581.7(b), under the conditions of Sec. 581.6, at an impact speed of 1.5 m.p.h., and when impacted by a pendulum-type test device in accordance with the procedures of Sec. 581.7(a) at 2.5 m.p.h., followed by an impact into a fixed collision barrier that is perpendicular to the line of travel of the vehicle, while traveling longitudinally forward, then longitudinally rearward, under the conditions of Sec. 581.6, at 2.5 m.p.h. (b) [Reserved] (c) Protective criteria. (1) Each lamp or reflective device except license plate lamps shall be free of cracks and shall comply with applicable visibility requirements of S4.3.1.1 of Standard No. 108 (Sec. 571.108 of this part). The aim of each headlamp shall be adjustable to within the beam aim inspection limits specified in Table 2 of SAE Recommended Practice J599b, July 1970, measured with a mechanical aimer conforming to the requirements of SAE Standard J602a, July 1970. (2) The vehicle's hood, trunk, and doors shall operate in the normal manner. (3) The vehicle's fuel and cooling systems shall have no leaks or constricted fluid passages and all sealing devices and caps shall operate in the normal manner. (4) The vehicle's exhaust system shall have no leaks or constrictions. (5) The vehicle's propulsion, suspension, steering, and braking systems shall remain in adjustment and shall operate in the normal manner. (6) A pressure vessel used to absorb impact energy in an exterior protection system by the accumulation of gas pressure or hydraulic pressure shall not suffer loss of gas or fluid accompanied by separation of fragments from the vessel. (7) The vehicle shall not touch the test device, except on the impact ridge shown in Figures 1 and 2, with a force that exceeds 2000 pounds on the combined surfaces of Planes A and B of the test device. (8) The exterior surfaces shall have no separations of surface materials, paint, polymeric coatings, or other covering materials from the surface to which they are bonded, and no permanent deviations from their original contours 30 minutes after completion of each pendulum and barrier impact, except where such damage occurs to the bumper face bar and the components and associated fasteners that directly attach the bumper face bar to the chassis frame. (9) Except as provided in Sec. 581.5(c)(8), there shall be no breakage or release of fasteners or joints. [42 FR 24059, May 12, 1977, as amended at 42 FR 38909, Aug. 1, 1977; 43 FR 40231, Sept. 11, 1978; 47 FR 21837, May 20, 1982] Sec. 581.6 Conditions. The vehicle shall meet the requirements of Sec. 581.5 under the following conditions. (a) General. (1) The vehicle is at unloaded vehicle weight. (2) The front wheels are in the straight ahead position. [[Page 772]] (3) Tires are inflated to the vehicle manufacturer's recommended pressure for the specified loading condition. (4) Brakes are disengaged and the transmission is in neutral. (5) Trailer hitches, license plate brackets, and headlamp washers are removed from the vehicle. Running lights, fog lamps, and equipment mounted on the bumper face bar are removed from the vehicle if they are optional equipment. (b) Pendulum test conditions. The following conditions apply to the pendulum test procedures of Sec. 581.7 (a) and (b). (1) The test device consists of a block with one side contoured as specified in Figure 1 and Figure 2 with the impact ridge made of A1S1 4130 steel hardened to 34 Rockwell ``C.'' The impact ridge and the surfaces in Planes A and B of the test device are finished with a surface roughness of 32 as specified by SAE Recommended Practice J449A, June 1963. From the point of release of the device until the onset of rebound, the pendulum suspension system holds Plane A vertical, with the arc described by any point on the impact line lying in a vertical plane (for Sec. 581.7(a), longitudinal; for Sec. 581.7(b), at an angle of 30 deg. to a vertical longitudinal plane) and having a constant radius of not less than 11 feet. (2) With Plane A vertical, the impact line shown in Figures 1 and 2 is horizontal at the same height as the test device's center of percussion. (3) The effective impacting mass of the test device is equal to the mass of the tested vehicle. (4) When impacted by the test device, the vehicle is at rest on a level rigid concrete surface. (c) Barrier test condition. At the onset of a barrier impact, the vehicle's engine is operating at idling speed in accordance with the manufacturer's specifications. Vehicle systems that are not necessary to the movement of the vehicle are not operating during impact. (Sec. 102, Pub. L. 92-513, 86 Stat. 947 (15 U.S.C. 1912); secs. 103, 119, Pub. L. 89-563, 80 Stat. 718 (15 U.S.C. 1392, 1407); delegation of authority at 49 CFR 1.50 and 501.7) [42 FR 24059, May 12, 1977, as amended at 42 FR 38909, Aug. 1, 1977; 48 FR 43331, Sept. 23, 1983] Sec. 581.7 Test procedures. (a) Longitudinal impact test procedures. (1) Impact the vehicle's front surface and its rear surface two times each with the impact line at any height from 16 to 20 inches, inclusive, in accordance with the following procedure. (2) For impacts at a height of 20 inches, place the test device shown in Figure 1 so that Plane A is vertical and the impact line is horizontal at the specified height. (3) For impacts at a height between 20 inches and 16 inches, place the test device shown in Figure 2 so that Plane A is vertical and the impact line is horizontal at a height within the range. (4) For each impact, position the test device so that the impact line is at least 2 inches apart in vertical direction from its position in any prior impact, unless the midpoint of the impact line with respect to the vehicle is to be more than 12 inches apart laterally from its position in any prior impact. (5) For each impact, align the vehicle so that it touches, but does not move, the test device, with the vehicle's longitudinal centerline perpendicular to the plane that includes Plane A of the test device and with the test device inboard of the vehicle corner test positions specified in Sec. 581.7(b). (6) Move the test device away from the vehicle, then release it to impact the vehicle. (7) Perform the impacts at intervals of not less than 30 minutes. (b) Corner impact test procedure. (1) Impact a front corner and a rear corner of the vehicle one each with the impact line at a height of 20 inches and impact the other front corner and the other rear corner once each with the impact line at any height from 16 to 20 inches, inclusive, in accordance with the following procedure. (2) For an impact at a height of 20 inches, place the test device shown in Figure 1 so that Plane A is vertical and the impact line is horizontal at the specified height. (3) For an impact at a height between 16 inches and 20 inches, place the test device shown in Figure 2 so that Plane A is vertical and the impact line is horizontal at a height within the range. (4) Align the vehicle so that a vehicle corner touches, but does not move, the [[Page 773]] lateral center of the test device with Plane A of the test device forming an angle of 60 degrees with a vertical longitudinal plane. (5) Move the test device away from the vehicle, then release it to impact the vehicle. (6) Perform the impact at intervals of not less than 30 minutes. [GRAPHIC] [TIFF OMITTED] TC01AU91.197 [42 FR 24059, May 12, 1977, as amended at 42 FR 38909, Aug. 1, 1977]